Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 130

background image

BA 5001-6001 US – Edition 1.2 * 6001b510.fm

5-7

Maintenance

Bleeding the fuel system

WARNING

Fire and burn hazard. Draining fuel may ignite if it comes into contact with hot
engine parts or the exhaust system. Hot fuel may cause burns.

☞

Always wear protective equipment and safety glasses when working with
fuel.

☞

Never bleed the fuel system if the engine is hot.

Bleed the fuel system in the following cases:
• After removing and fitting the fuel filter, prefilter or the fuel lines back on again.
• After running the fuel tank empty.
• After running the engine again, after it has been out of service for a longer period of

time.

Bleed the fuel system as follows:

☞

Fill the fuel tank.

☞

Turn the starter key to the first position.

☞

Wait about 5 minutes while the fuel system bleeds itself automatically.

☞

Start the engine.

If the engine runs smoothly for a while and then stops; or if it does not run smoothly:

☞

Stop the engine.

☞

Bleed the fuel system again as described above.

☞

Have this checked by authorized staff if necessary.

«
...
83
84
85
86
87
...
»

Содержание Dumper 5001



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dumper 5001

Бренд: JB-Lighting Страницы: 40

Pro Vantage 12+ Series

Бренд: Ecco Страницы: 6

Бренд: Hantek Страницы: 124

Бренд: Hameg Страницы: 10

Бренд: Mackie Страницы: 34

Бренд: Mackworth Страницы: 38

Бренд: P&P Страницы: 6

Бренд: PARUS Страницы: 6

Бренд: Saadat Страницы: 61

Бренд: Saadat Страницы: 22

MIAMI J ADVANCED

Бренд: Össur Страницы: 35

Бренд: Össur Страницы: 38

Бренд: Össur Страницы: 8

Бренд: Össur Страницы: 72

Бренд: Össur Страницы: 76

Miami Lumbar Posteo

Бренд: Össur Страницы: 45

Бренд: Össur Страницы: 29

Icelock Clutch 211

Бренд: Össur Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды