Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 77

Страница: 77 / 130

BA 5001-6001 US – Edition 1.2 * 6001b410.fm

4-1

Troubleshooting

4 Troubleshooting

The information given in this chapter is provided for maintenance staff, for fast and reliable
detection of malfunctions and their appropriate repair.
Repairs must be performed by authorized staff.

4.1

Engine trouble

Problem

Possible causes

See

Engine does not start or is not easy to start

Wrong SAE grade of engine lubrication oil

5-33

Fuel grade does not comply with specifications

5-33

Defective or flat battery

5-30

Loose or oxidized cable connections in starter circuit

Defective starter, or pinion does not engage

Wrong valve clearance

Defective fuel injector

Engine starts, but does not run smoothly or faultless

Fuel grade does not comply with specifications

5-33

Wrong valve clearance

Injection line leaks

Defective fuel injector

Engine overheats. Temperature warning system
responds

Oil level too low

5-9

Oil level too high

5-9

Dirty air filter

5-14

Dirty oil radiator fins

Defective fuel injector

Insufficient engine output

Oil level too high

5-9

Fuel grade does not comply with specifications

5-33

Dirty air filter

5-14

Wrong valve clearance

Injection line leaks

Defective fuel injector

Engine does not run on all cylinders

Injection line leaks

Defective fuel injector

Insufficient or no engine oil pressure

Oil level too low

5-9

Machine inclination too high (max. 25 %)

Wrong SAE grade of engine lubrication oil

5-33

Engine oil consumption too high

Oil level too high

5-9

Machine inclination too high (max. 25 %)

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды