Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 81

Страница: 81 / 130

BA 5001-6001 US – Edition 1.2 * 6001b510.fm

5-3

Maintenance

Front dump bucket maintenance strut (6001)

WARNING

Crushing or striking hazard. An improperly supported dump bucket can fall
unexpectedly during maintenance work.

☞

Fold down the red maintenance strut before you perform maintenance work
with the dump bucket raised.

Procedure to follow:

☞

Raise the dump bucket.

☞

Remove split pin

out of lock pin

☞

Pull out lock pin

☞

Hold maintenance strut

as you do so.

☞

Fold down maintenance strut

WARNING

Personal injury hazard. Persons can be struck or crushed by a dump bucket
that is being lowered too quickly.

☞

To insert the retaining pin, slowly and carefully lower the dump bucket to
align the hole in the bracket with the hole in the maintenance strut.

☞

Lower the dump bucket until maintenance strut

fits into bracket

☞

Fasten maintenance strut

in bracket

with lock pin

☞

Insert split pin

in lock pin

Important

Fasten maintenance strut

on the dump bucket again (in the reverse order)

once maintenance work is over.

Fig. 71: Front dump bucket maintenance strut

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды