Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 68

Страница: 68 / 130

3-36

BA 5001-6001 US – Edition 1.2 * 6001b330.fm

Operation

3.21 Rollbar

CAUTION

Personal injury hazard. The rollbar is very heavy and should not be raised or
lowered by one person.

☞

Two persons are required for raising or lowering the rollbar.

Important

Fasten the seat belt only if the rollbar is raised.

Raising the rollbar:

☞

Place the machine on level ground.

☞

Raise the rollbar with the help of a second person.

☞

Secure the rollbar with lock pins

☞

Secure lock pins

with split pins

☞

Fold down ring

➥

Split pin

cannot fall out.

Lowering the rollbar:

☞

Place the machine on level ground.

☞

Fold up ring

☞

Remove split pins

from lock pins

☞

Remove lock pins

☞

Slowly and carefully lower the rollbar with the help of a second person.

Fig. 59: Rollbar

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды