Tuttnauer 2301006 Скачать руководство пользователя страница 94

Страница: 94 / 122

Page 89 of 117 pages

11.7 Cleaning and Replacing the Water Level Electrodes

The two electrodes of the water level control system are located on

top of the STS generator.

Cleaning

Turn off the electric power and release the steam

pressure from the autoclave and the steam

generator.

Disconnect the wire from the electrodes

connections.

Open the nuts that tighten the electrodes.

Insert a new electrode and tighten the fixing bolt

to avoid leakage.

Reconnect the wires to the electrodes

Replacing

Remove the two electrodes. Keep in mind the

place of the short and long electrodes.

Clean the electrodes.

Reassemble the two electrodes into their places.

Tighten the nuts to avoid leakage.

Reconnect the wire to the electrodes.

Test the unit.

Содержание 2301006



























































































































Результаты поиска

Содержание 2301006

Отзывы:

Похожие инструкции для 2301006

Бренды по названию

Популярные бренды

Tuttnauer 2301006, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 2301006

Отзывы:

Похожие инструкции для 2301006

Бренды по названию

Популярные бренды