Tuttnauer 2301006 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 122

Tuttnauer 2301006 Скачать руководство пользователя страница 59

Page 54 of 117 pages

4.3.4 Changing Cycle Parameters

The screen that allows for parametric changes appears as follows:
Pressing Clear or Enter before entering the code returns to the Stand By screen,
and the RUN & FAIL LED's are lit.
Enter the correct code only via the UP/DN keypads, press ENTER to proceed to
the next screen.
Pressing the UP/DN keypads can also change all parameter values.

Cycle Setup Parameters:

Code 1 or 11 Parameters

STE Temp – Required sterilization temperature for the process

Entry code

1 or 11

Resolution

34ºF

Minimum value

221ºF

Maximum value

280ºF

STE Time – Required sterilization time for the process
Entry code

1 or 11

Resolution

1 minute

Minimum value

Ø minutes

Maximum value

59 minutes

Dry Time – Required drying time for the process:
Entry code

1 or 11

Resolution

1 minute

Minimum value

Ø minutes

Maximum value

59 minutes

Heat T.O. – Maximum time for heating the chamber for starting sterilization

When the duration of the heating stage is longer than Heat T.O., the program will
collapse with the message ‘Low Heat’.

Entry code

11

Resolution

10 seconds

Minimum value

1200 seconds (20 minutes)

Maximum value

3600 seconds (minutes)

«
...
57
58
59
60
61
...
»

Содержание 2301006



























































































































Отзывы:

Нет отзывов