Tuttnauer 2301006 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 122

Tuttnauer 2301006 Скачать руководство пользователя страница 6

Page 1 of 117 pages

INCOMING INSPECTION

The instruments (products) should be unpacked and inspected for mechanical
damage upon receipt. Observe packing method and retain packing materials until the
unit has been inspected.
Mechanical inspection involved checking for signs of physical damage such as:
scratched panel surfaces, broken knobs, etc.

If damage is apparent, file a claim with the carrier. The manufacturer is responsible
for products shipped F.O.B. These products are carefully inspected prior to shipment
and all reasonable precautions are taken in preparing them for shipment to assure
safe arrival at their destination.

WARRANTY

We certify that this instrument is guaranteed to be free from defects in material and

workmanship for one year against faulty components and assembly with the

exception of glassware, lamps and heaters.

The warranty does not include and does not replace routine treatment and preventive

maintenance to be performed according to instructions in paragraph 11.1 'Preventive

and Periodical Maintenance'.

Our obligation is limited to replacing the instrument or parts, after our examination, if

within one year after the date of shipment they prove to be defective. This warranty

does not apply to any instrument, which has been subjected to misuse, neglect,

accident or improper installation or application, nor shall it extend to products, which

have been repaired or altered outside the factory without prior authorization from us.

The Autoclave should not be used in a manner not described in this manual!

Note

If there is any difficulty with this instrument, and the solution is not covered in this
manual, contact our representative or us first.

Do not attempt to service this instrument yourself.

Stipulate

the model

and

serial number

and describe the difficulty as clearly as

possible so we may be able to diagnose the problem and hence provide a prompt
solution.

For technical information or service please contact our representative at:

Tuttnauer USA Co.

25 Power Drive Hauppauge
NY, 11788, USA

Tel:(800)624 5836, (631)737 4850

¬

Fax:(631)737 07 20

Email:

[email protected]

Our web site:

www.tuttnauer.com

«
...
4
5
6
7
8
...
»

Содержание 2301006



























































































































Отзывы:

Нет отзывов