Tuttnauer 2301006 Скачать руководство пользователя страница 91

Страница: 91 / 122

Page 86 of 117 pages

11.4 Troubleshooting for the Water Pump ‘SHURFLO’

Symptom

Possible cause

Corrections

1. Pump does not

start.

1.1 Fuse burnt or circuit

breaker tripped.

1.2 Wrong voltage.
1.3 Damaged electrical

connection.

1.4 Faulty pressure switch.
1.5 Open or grounded circuit

due to faulty rectifier or
motor.

1.6 Locked drive assembly.

1.1 Replace fuse or

turn on the circuit
breaker.

1.2 Use right voltage.
1.3 Fix connections.
1.4 Replace pump.
1.5 Replace pump.
1.6 Replace pump.

2. Pump does not

prime (motor runs
but water is not
discharged.

2.1 No water supply.
2.2 Inlet water strainer

clogged.

2.3 Vacuum leak in inlet

line.

2.4 Inlet or outlet tube

severely kinked.

2.5 Debris in pump inlet or

outlet valves.

2.6 Pump operating on

wrong voltage.

2.7 Pump housing damaged

(cracks).

2.1 Fix water supply.
2.2 Clean inlet strainer.
2.3 Replace piping.
2.4 Straighten or

replace tube.

2.5 Clean valves.
2.6 Use right voltage.
2.7 Replace pump.

3. Leak from pump

head or switch.

3.1 Loose screws at switch

or pump head.

3.2 Switch diaphragm

ruptured or pinched

3.1 Fasten screws
3.2 Replace damaged

pump.

4. Pump will not

shut-off

4.1 Output line closed and

no leaks.

4.2 Air trapped in outlet line

or pump head.

4.3 Pump operating on

wrong voltage.

4.4 Inlet or outlet valves

clogged.

4.5 Loose drive assembly or

pump head screw.

4.6 pressure switch

operation/adjustment
incorrect

4.1 Open outlet line.
4.2 Remove trapped

air.

4.3 Use right voltage.
4.4 Clean clogged

valves.

4.5 Fasten loose

screws.

4.6 Refer to S/B #1031

for differential and
pressure
adjustment
procedure.

5. Pump runs loudly

5.1 Loose pump head or drive

screws.

5.1 Tighten loose

screws.

Содержание 2301006



























































































































Результаты поиска

Содержание 2301006

Отзывы:

Tuttnauer 2301006, Руководство по эксплуатации и техническому обслуживанию, Страница: 91 / 122

Результаты поиска

Содержание 2301006

Отзывы: