TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 97

Страница: 97 / 146

Page

D-23

MAINTENANCE

Document 57.0003.4200 - 03/2005

Handler with telescopic boom

Agrilift 625 - Telelift 2506

■

Fuse box relays

Ref.

Circuit

K01

Starting enabling command

K02

Forward speed enabling command

K03

Inhibition with brake pedal stepped down

K04

Overload warning system control unit
enabling command

K05

Reverse speed enabling command

K06

Overload warning system solenoid valve
enabling command

ATTENTION

•

Do not use fuses having a higher amperage
than that recommended, since they can
damage the electric system seriously.

•

If the fuse blows after a short time, look for the
fault source by checking the electric system.

•

Always keep some spare fuses for an
emergency.

•

Never try to repair or short blown fuses.

•

Make sure the contacts of fuses and fuse-
sockets ensure a good electric connection and
are not oxidised.

■

Engine compartment fuses and relays

F31

Ref.

Circuit

Amp

F30

Preheating control unit maxifuse

F31

System protection fuse

K11

Start relay

A02

Preheating control unit

K01

K02

K03

K04

K06

K05

F10

F11

F12

F13

F14

F15

F16

F17

F18

F19

F20

F21

F22

F23

F24

F25

F26

F27

F28

F29

INT

K11

F30

A02

Courtesy of Crane.Market

Содержание Agrilift 625



















































































































































Результаты поиска

Содержание Agrilift 625

Отзывы:

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 97 / 146

Результаты поиска

Содержание Agrilift 625

Отзывы: