TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 45

Страница: 45 / 146

Page

C-9

OPERATING INSTRUCTIONS

Document 57.0003.4200 - 03/2005

Handler with telescopic boom

Agrilift 625 - Telelift 2506

C-3.2

ENGINE CONTROLS AND

INSTRUMENTS

■

C-3.2.1

Ignition switch

Three-position switch:

No circuit under voltage, key can be removed
and engine is stopped

Circuits under voltage, presetting for the engine
starting. Board controls and instruments are on.
The warning light

signalling the glow plugs

preheating comes on. Wait until the light goes
off before starting the engine.

Engine starting; when released, key springs

back to pos.

automatically.

■

C-3.2.2

Forward/reverse gear selector switch

Three-position switch with lock in neutral position:

Neutral position; no gear engaged

Shift lever to pos.

to select the forward gear

Shift lever to pos.

to select the reverse gear

120





��



Courtesy of Crane.Market

Содержание Agrilift 625



















































































































































Результаты поиска

Содержание Agrilift 625

Отзывы:

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 45 / 146

Результаты поиска

Содержание Agrilift 625

Отзывы: