TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 66

Страница: 66 / 146

Page

C-30

OPERATING INSTRUCTIONS

Document 57.0003.4200 - 03/2005

Handler with telescopic boom

Agrilift 625 - Telelift 2506

■

C-5.3 HANDLING LOADS

■

C-5.3.1 Adjusting the forks

Forks shall be spaced to suit the load going to be
handled. For this purpose:

•

Lift the clamping lever of the forks.

•

Slide the forks to the desired position, then re-lock
the lever.

CAUTION

•

The centre of gravity of the load must always
be halfway between the forks.

•

Ensure you exactly know the weight of the load
before handling it.

•

When extending the boom, do not exceed the
payload limit.

•

Refer to the payload limits given in the load
chart applied on the cab windscreen or in the
quick user’s guide.

•

Space the forks as wide as possible to suit the
load being handled.

In the case of floating forks:

•

Loosen the nut of the locking screws.

•

Raise the forks and slide them on the pivot until
correct spacing.

•

Lock the screws re-tightening the nut.

Courtesy of Crane.Market

Содержание Agrilift 625



















































































































































Результаты поиска

Содержание Agrilift 625

Отзывы:

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 66 / 146

Результаты поиска

Содержание Agrilift 625

Отзывы: