TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 39

Страница: 39 / 146

Page

C-3

OPERATING INSTRUCTIONS

Document 57.0003.4200 - 03/2005

Handler with telescopic boom

Agrilift 625 - Telelift 2506

��

C-2 ENTERING THE MACHINE

■

C-2.1 ENTERING THE CAB

CAUTION

Always make sure that your hands and shoe soles
are clean and dry before getting into the driving
cab. Always face the machine when entering and
leaving it and hold to the suitable handles.

The handler cab is equipped with an access door on
the left-hand side.

Door opening from outside:

•

Insert the key and release lock

•

Press the pushbutton and open the door.

Door closing from inside:

•

Pull the door with force: it locks automatically.

Door opening from inside:

•

Lift lever

and release the lock to open the door

completely.

•

Rotate handle

to open the upper section of the

door and lock it against the special catch.

To unlock the door latched in open position:

•

Press button

to unlock the door from the catch,

close and latch the door to the lower section using
handle

CAUTION

The upper section of the door must be secured to
the rear part of the driving cab or latched to the
lower section of the same door.

Courtesy of Crane.Market

Содержание Agrilift 625



















































































































































Результаты поиска

Содержание Agrilift 625

Отзывы:

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 39 / 146

Результаты поиска

Содержание Agrilift 625

Отзывы: