TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 103

Страница: 103 / 146

Page

E-3

FAULTS AND TROUBLESHOOTING

Document 57.0003.4200 - 03/2005

Handler with telescopic boom

Agrilift 625 - Telelift 2506

NO BOOM LOWERING AND
EXTENSION, NO HOLDING FRAME
TILTING

THE HYDRAULIC OIL
THERMOMETER DOES NOT WORK

THE PARKING BRAKE LIGHT
DOES NOT LIGHT UP

BOOM DOES NOT MOVE

THE LOAD LIMITING SYSTEM DOES
NOT CHANGE WORK SCALE

THE LOAD LIMITING SYSTEM IS
BLOCKED
(red LED’s lit)

CHECKING THE MICRO-SWITCHES
WHEN THE ARB IS IN ALARM, THE
BOOM IN/OUT MOVEMENTS, THE
OUTRIGGER UP-MOVEMENT AND
THE MACHINE SWAY FUNCTION
REMAIN ACTIVATED

CHECKING THE MICRO-SWITCHES
WITH THE BOOM RAISED 2
METRES ABOVE THE GROUND THE
OUTRIGGER UP-MOVEMENT AND
THE MACHINE SWAY FUNCTION
REMAIN ACTIVATED

• Fuse blown
• Emergency button ON

• This is normal, when the outside tem-

perature is low and/or the machine is
used for short periods, since the
hydraulic oil cannot warm up over
40

• Fuse blown

• “ROAD/JOBSITE” switch set to

“ROAD”

• Emergency button ON

• Outriggers limit switches inefficient

• Low stability

• Check that the connectors are

correctly plugged in the actuator

• Check that the connectors are

correctly plugged in the actuator

• Replace fuses

and/or

F24

• Reset the button

• Check and replace fuse

, if

necessary

• Check and replace fuse

F22

, if

necessary

• Set to “CAB”

• Reset the button

• Check the efficiency of the

outrigger limit switches or replace
if necessary.

• Retract the load within safety

limits.

If the error message is still shown,

move the boom to rest condition
operating the overload warning
system cutout key and contact
your nearest authorised service
centre.

• If the connectors are plugged in

correctly, contact the TEREXLIFT
Technical Assistance

• If the connectors are plugged in

correctly, contact the TEREXLIFT
Technical Assistance

Courtesy of Crane.Market

Содержание Agrilift 625



















































































































































Результаты поиска

Содержание Agrilift 625

Отзывы:

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 103 / 146

Результаты поиска

Содержание Agrilift 625

Отзывы: