manualshive.com logo in svg

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 22 / 146

Поделиться
Скачать
TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 22

Page

  

A-14

GENERAL INFORMATION

Document 57.0003.4200 - 03/2005

Handler with telescopic boom 

 Agrilift 625 - Telelift 2506

■

  A-3.5    SAFETY DEVICES

• Load limiting device.  A load cell is fitted to the rear

axle. The cab display with 8 LED’s (4 green, 2 yellow
and 2 red) lets you estimate the variation of stability
of the machine.

• Emergency stop pushbutton: when pressed down,

it stops the engine and blocks the movements of
the machine.

Before starting work again, find and rectify the
causes which compelled to an emergency stop,
then reset the button to neutral position pressing it
down while turning clockwise.

• Safety pushbutton on joystick (dead man button)

.

(Not present in the TCE version)

This button must be pressed and held down while
executing a function with the control lever. If the
button is released, the movement in progress will
be blocked.

• Presence micro-switch in the driving seat

(only in the TCE version)

Located inside the seat cushion, it prevents any
machine starting if the operator is not correctly
seated in the driving seat.

Courtesy of Crane.Market 

Содержание Agrilift 625



















































































































































Отзывы:

Нет отзывов