manualshive.com logo in svg

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 61 / 146

Поделиться
Скачать
TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 61

Page

  

C-25

OPERATING INSTRUCTIONS

Document 57.0003.4200 - 03/2005

Handler with telescopic boom 

 Agrilift 625 - Telelift 2506

■

 

 C-4.4

LOW TEMPERATURE STARTING

In case of cold starting, use an oil with a SAE viscosity
adequate to the ambient temperature.

Please refer to the DEUTZ engine use and maintenance
manual.

The machine is supplied with oil SAE 15W/40.

To start the engine from cold, proceed as follows:

•

Put the mechanical gear lever to neutral.

•

Turn the ignition switch to position 

 

and wait until

the warning light 

28 

signalling the glow plugs

preheating goes off. Step down on the gas pedal
and start the engine turning the ignition switch to

.

 

Release as soon as the engine starts.

•

Let the engine run at idle for a few seconds before
putting a gear; this allows for a gradual warm up of
the engine oil and a better lubrication.

•

In case of engine jump-starting, remove the booster
ables (see chapter C-4.3).

■

 

 C-4.5

DISCONNECTING THE BATTERY

During maintenance or repair works, and while welding,
turn off the battery main switch 

,

 

located behind the

rear right wheel compartment.

■

 

 C-4.6

STARTING THE MACHINE

When the engine reaches the running temperature,
ensure all parts are in transfer position and the gearbox
lever is in neutral. Then, proceed as follows:

•

Select the required steering mode.

•

Select the required gear (forward or reverse).

•

Release the parking brake pressing button 

19

 (the

warning light on the pushbutton must be off).

•

Slowly step on the gas pedal to start moving off.

CAUTION

Do not operate the forward/reverse gear lever when
the machine is running. The machine would reverse
the running direction abruptly and you could
seriously be injured.

Courtesy of Crane.Market 

Содержание Agrilift 625



















































































































































Отзывы:

Нет отзывов