TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 72

Страница: 72 / 146

Page

C-36

OPERATING INSTRUCTIONS

Document 57.0003.4200 - 03/2005

Handler with telescopic boom

Agrilift 625 - Telelift 2506

■

C-6.3

LIFTING THE MACHINE

When the machine shall be lifted, use only means
having a suitable capacity. The characteristic data are
detailed in the relevant chapter of this manual and on
the identification plate.

For the machine lifting, anchor the chains to the special
lugs on the machine (marked with the decal below).

■

C-6.4

TRANSPORTING THE MACHINE ON
OTHER VEHICLES

To transport the machine on another vehicle, follow the
steps below:

•

Put chocks at the machine wheels.

•

Ensure ramps are correctly positioned.

•

Retract the boom to transfer position.

•

Carefully drive the machine onto the transporting
vehicle.

•

Put the parking brake and rest the attachment flat
on the vehicle platform.

•

Ensure the overall dimensions do not exceed the
allowed limits.

•

Shut the engine down and close the driving cab of
the machine.

•

Secure the machine to the vehicle platform by
wheel-chocks.

•

Anchor the machine to the transporting vehicle with
suitable chains.

Courtesy of Crane.Market

Содержание Agrilift 625



















































































































































Результаты поиска

Содержание Agrilift 625

Отзывы:

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 72 / 146

Результаты поиска

Содержание Agrilift 625

Отзывы: