manualshive.com logo in svg

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 92 / 146

Поделиться
Скачать
TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 92

Page

  

D-18

MAINTENANCE

Document 57.0003.4200 - 03/2005

Handler with telescopic boom 

 Agrilift 625 - Telelift 2506

■

  

D-3.14 ADJUSTING THE SLIDING PADS OF

THE BOOM SECTIONS

Any boom section is fitted with adjustable pads located
on the four sides of the profile. These pads are secured
to both fixed and mobile part of every section.

All pads can be adjusted by the special shims supplied
by TEREXLIFT upon demand.

Adjusting the pads

:

•

Remove or loosen the screws fixing the pads in
relation to type of shims used (with or without
slots).

•

Fit the necessary amount of shims.

•

If the residual thickness of the pad is insufficient or
near the maximum wearing limit, renew the pad.

•

Tighten the screws fixing the pads at the
recommended torque (see below). Use a
dynamometric wrench.

Tightening torques of the pad screws in relation to
the screw diameter

Screws M10

Nm 30

Screws M14

Nm 50

Tightening torques higher than those recommended
can cause the break of the pad or of the locking
threaded bush.

ATTENTION

Pads must compulsorily be replaced if the residual
thickness of the plastic layer with respect to the
iron bush fixing the block is equal or inferior to 1
mm.

Minimum 1 mm

Max. wearing thickness

  

SERVICE INTERVAL

Running-in ____________________________

None

Ordinary ___________________

When necessary

Courtesy of Crane.Market 

Содержание Agrilift 625



















































































































































Отзывы:

Нет отзывов