manualshive.com logo in svg

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 93 / 146

Поделиться
Скачать
TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 93

Page

  

D-19

MAINTENANCE

Document 57.0003.4200 - 03/2005

Handler with telescopic boom 

 Agrilift 625 - Telelift 2506

■

 

D-3.15

CHECKING THE SAFETY DEVICES

■

  

Checking the load limiting system

(at every use)

When power is turned on, the DLE load limiting system
runs a self-test. In the case of troubles, LED’s 

5

, 

8

 and

10

 start flashing, the buzzer sounds, an error code is

shown on the display and the machine enters the alarm
mode and cannot be operated.
The meaning of the error messages is shown in Section

E

 “

Faults and

 

Troubleshooting”

.

To do a manual check, it will be enough to load a weight
exceeding the maximum permitted with the boom fully
out and attempt to lift it. The system shall enter in alarm;
should that not be the case, contact TEREXLIFT
Technical Service.

■

  

Checking the emergency stop pushbutton

     

(at every use)

To check the efficiency of this pushbutton, simply
press it down during a movement. The pressure of the
pushbutton shall cause the movement to stop and the
engine to shut down. Should that not be the case,
contact TEREXLIFT Technical Service.

■

  

Checking the joystick pushbutton 

(not present in

the TCE version)

(at every use)

To check if the pushbutton on the control lever is in
efficient working order, it will be enough to attempt to
operate the lever without pressing this button.
In this condition, the lever shall not operate any
movement. Should that not be the case, contact
TEREXLIFT Technical Service.

10

5

8

■

  

Checking the machine start control

(at every use)

Attempt to start the engine with the forward or reverse
gear put.

The engine must not start. If the engine starts, contact
the TEREXLIFT Technical Service.

Repeat the operation putting first one gear, then the
other.

■

Checking the seat micro-switch 

(only in the TCE

version)

(at every use)

To check if the seat micro-switch is in efficient working
order, simply attempt to start the machine without
being seated. The machine must remain stopped.
Should that not be the case,

 

contact TEREXLIFT

Technical Service.

Courtesy of Crane.Market 

Содержание Agrilift 625



















































































































































Отзывы:

Нет отзывов