TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 84

Страница: 84 / 146

Page

D-10

MAINTENANCE

Document 57.0003.4200 - 03/2005

Handler with telescopic boom

Agrilift 625 - Telelift 2506

■

D-3.6

ENGINE AIR FILTER

Clean the engine air filter every 10 hours; replace the
filtering element, if necessary.

Cleaning and changing the external element:

- Stop the engine and engage the parking brake.
- Unscrew wingnut

and remove cover

- Unscrew wingnut

and remove the outer

element

- Clean the filter bowl.

- Clean the cartridge by beating it some times on

the ground paying attention not to damage the
filtering element.
Do not dry-clean the filtering element.

- Check for cracks in the filtering element by

introducing a lamp inside.

- Smear the seal with grease, then refit the element.

- Tighten wingnut

, close cover

and tighten

with wingnut

ATTENTION

As soon as the warning lamp on the cab dashboard
switches on, replace the outer element.

SERVICE INTERVAL

Running-in ___________________________

None

Cleaning ___________________

Every

hours

Filtering element substitution _

Every

500

hours









Courtesy of Crane.Market

Содержание Agrilift 625



















































































































































Результаты поиска

Содержание Agrilift 625

Отзывы:

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 84 / 146

Результаты поиска

Содержание Agrilift 625

Отзывы: