manualshive.com logo in svg

TEREXLIFT Agrilift 625, Руководство оператора, Страница: 80 / 146

Поделиться
Скачать
TEREXLIFT Agrilift 625 Скачать руководство пользователя страница 80

Page

  

D-6

MAINTENANCE

Document 57.0003.4200 - 03/2005

Handler with telescopic boom 

 Agrilift 625 - Telelift 2506

■

  D-3.2

ACCESS TO THE ENGINE AND
TANKS COMPARTMENTS

■

Engine compartment

For any operation within the engine compartment,
open the protection bonnet.
Hood is equipped with lock & key and a supporting rod
that holds it in position.
From the engine compartment, you get access to:
•

Thermal engine

•

Engine air filter 

•

Hydraulic oil tank plug

•

Radiator fluid compensation cup

•

Battery

To get access to the engine compartment:

•

Shut the engine down and put the parking brake.

•

Unlock the bonnet lock 

•

Lift the bonnet using the special handle 

 until it

latches in the gas spring.

•

To close the bonnet: press on the green locking
device 

 

on the gas spring and lower the bonnet.

DANGER

Take all precautions when approaching
the engine compartment. Some parts
of the engine may be very hot. Always
use protective gloves.

■

Diesel fuel tank compartment

To gain access to the fuel tank, open the rear cover of
the machine 

 as follows:

•

Shut the engine down and put the parking brake.

•

Fully raise the cover by means of the special
handle.

Courtesy of Crane.Market 

Содержание Agrilift 625



















































































































































Отзывы:

Нет отзывов