Terex Genie Lift Connect Скачать руководство пользователя страница 9

Страница: 9 / 67

Rev C

Instructions

Procedure - S

and Z® Booms

Part No. 1295251GT

Lift Connect

™

2 Remove and discard the protective film from

the adhesive tape located on the bottom of the

telematics bracket.
Genie part number 1289561GT.

3 Adhere the bracket to the control box.
Note: Mount the bracket 3 inches / 7,6 cm from the

right side of the control box.
Note: The adhesive takes approximately 20

minutes to fully adhere to the surface.
4 Secure the telematics module to the mounting

bracket using the provided retaining fasteners.
Genie part number 1289520GT or

1289521GT.

1  retaining fasteners
2  telematics module
3  telematics bracket

5 Connect the telematics module to the retrofit

harness.
Genie part number 1292977GT.

Note: Harness connectors are keyed for proper

installation.

Component damage hazard.

Improper connections will result

in damage to the telematics

module and it is not covered

under warranty.

example of keyed harness connector

6 Connect the loose end of the retrofit harness

to the 8 pin connector located on the right side

of the control box.

1  telematics module
2  ground control box
3  connector, 8 pin

Содержание Genie Lift Connect




































































Результаты поиска

Содержание Genie Lift Connect

Отзывы:

Похожие инструкции для Genie Lift Connect

Бренды по названию

Популярные бренды

Terex Genie Lift Connect, Руководство по установке

Результаты поиска

Содержание Genie Lift Connect

Отзывы:

Похожие инструкции для Genie Lift Connect

Бренды по названию

Популярные бренды