Terex Genie Lift Connect Скачать руководство пользователя страница 41

Страница: 41 / 67

Rev C

Instructions

™

Models

Part No. 1295251GT

Lift Connect

™

7 Adhere the bracket to the top of the pivot link.
Note: Mount the bracket in the center of the pivot

link.
Note: The adhesive takes approximately 20

minutes to fully adhere to the surface.
8 Secure the telematics module to the mounting

bracket using the provided retaining fasteners.
Genie part number 1289520GT or

1289521GT.

1  retaining fasteners
2  telematics module
3  telematics bracket

9 Open the ground controls compartment and

locate the 8 pin connector behind the ground

control box.

10 Connect the gateway harness to the 8 pin

connector.
Genie part number 1289899GT.

Note: Harness connectors are keyed for proper

installation.

Component damage hazard.

Improper connections will result

in damage to the telematics

module and it is not covered

under warranty.

example of keyed harness connector

11 Connect the pin switch jumper to the gateway

harness.
Genie part number 1293512GT.

12 Route the harness through the access hole

under the function manifold and towards the

front of the machine.

Note: The front chassis cover can be removed if

extra space is required to route the harness.

Содержание Genie Lift Connect




































































Результаты поиска

Содержание Genie Lift Connect

Отзывы:

Похожие инструкции для Genie Lift Connect

Бренды по названию

Популярные бренды

Terex Genie Lift Connect, Руководство по установке

Результаты поиска

Содержание Genie Lift Connect

Отзывы:

Похожие инструкции для Genie Lift Connect

Бренды по названию

Популярные бренды