Terex Genie Lift Connect Скачать руководство пользователя страница 61

Страница: 61 / 67

Rev C

Instructions

Light Towers - AL™, RL™ Models

Part No. 1295251GT

Lift Connect

™

AL5, AL5V, AL5HT

This procedure only applies to the following serial

numbers listed below.

from serial number

AL515-1616

AL5HT15-201

Note: Perform this procedure on a firm, level

surface.
1 Using a mild cleaning solvent, clean the front

of the cabinet.

AL5, AL5V - models without external power option

AL5, AL5V - models with external power option

AL5HT

1 telematics bracket

2 Remove and discard the protective film from

the adhesive tape located on the bottom of the

telematics bracket.
Genie part number 1289561GT.

3 Adhere the bracket to the front of the cabinet.
Note: Mount the bracket in the proper location

using the arrows in the previous illustrations.
Note: AL5HT models - position the bracket 2

inches / 5 cm to the left of the access hole.
Note: The adhesive takes approximately 20

minutes to fully adhere to the surface.

Содержание Genie Lift Connect




































































Результаты поиска

Содержание Genie Lift Connect

Отзывы:

Похожие инструкции для Genie Lift Connect

Бренды по названию

Популярные бренды

Terex Genie Lift Connect, Руководство по установке

Результаты поиска

Содержание Genie Lift Connect

Отзывы:

Похожие инструкции для Genie Lift Connect

Бренды по названию

Популярные бренды