Terex Genie Lift Connect Скачать руководство пользователя страница 58

Страница: 58 / 67

Instructions

Rev C

™

Models

Lift Connect

™

Part No. 1295251GT

5 Secure the telematics module to the mounting

bracket using the provided retaining fasteners.
Genie part number 1289520GT or

1289521GT or 1289522GT.

1  retaining fasteners
2  telematics module
3  telematics bracket

6 Connect the telematics module to the retrofit

harness.
Genie part number 1292198GT.

Note: Harness connectors are keyed for proper

installation.

Component damage hazard.

Improper connections will result

in damage to the telematics

module and it is not covered

under warranty.

example of keyed harness connector

7 Connect the loose end of the retrofit harness

to the 8 pin machine harness connector

located near the function pump.

8 Locate the machine serial label.
9 Using a mild cleaning solvent, clean an area

next to the serial label. Adhere one of the

provided ESN decals to the machine.

10 Note: The ESN decals are provided with the

telematics module.

11 Adhere the lexan cover decal over the ESN

decal.
Genie part number 1291624GT.

Register and activate the telematics

module. Refer to page 7.

Содержание Genie Lift Connect




































































Результаты поиска

Содержание Genie Lift Connect

Отзывы:

Бренды по названию

Популярные бренды

Terex Genie Lift Connect, Руководство по установке

Результаты поиска

Содержание Genie Lift Connect

Отзывы:

Бренды по названию

Популярные бренды