Terex Genie Lift Connect Скачать руководство пользователя страница 34

Страница: 34 / 67

Instructions

Rev C

™

and QS

™

Models

Lift Connect

™

Part No. 1295251GT

GR™ and QS™ M odels

GR-12, GR-15, GR-20, GRC-12,

QS-12R, QS-15R, QS-20R,

QS-12W, QS-15W, QS-20W

This procedure only applies to the following serial

numbers listed below.

from serial number

GR14-30931 to GRP-56587

GRC14-1781

QS14-1653

Note: Perform this procedure on a firm, level

surface with the machine in the stowed position.
1 Open the ground control compartment.
2 Using a mild cleaning solvent, clean the area

of the bulkhead where the telematics device

will be mounted.

1 telematics bracket

3 Remove and discard the protective film from

the adhesive tape located on the bottom of the

telematics bracket.
Genie part number 1289561GT.

4 Adhere the bracket to the bulkhead.
Note: The adhesive takes approximately 20

minutes to fully adhere to the surface.

5 Secure the telematics module to the mounting

bracket using the provided retaining fasteners.
Genie part number 1289520GT or

1289521GT.

1  telematics bracket
2  telematics module
3  retaining fasteners

6 Connect the gateway harness to the

telematics module.
Genie part number 1289899GT.

Note: Harness connectors are keyed for proper

installation.

Component damage hazard.

Improper connections will result

in damage to the telematics

module and it is not covered

under warranty.

example of keyed harness connector

Содержание Genie Lift Connect




































































Результаты поиска

Содержание Genie Lift Connect

Отзывы:

Похожие инструкции для Genie Lift Connect

Бренды по названию

Популярные бренды

Terex Genie Lift Connect, Руководство по установке

Результаты поиска

Содержание Genie Lift Connect

Отзывы:

Похожие инструкции для Genie Lift Connect

Бренды по названию

Популярные бренды