Steris P920011-649 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 168

background image

4-7

Processing Instructions

Operator Manual

920011-649

10. Determine if endoscope requires an insertion tube sleeve as

follows (see Figures 4-4 and 4-5):

NOTE: Insertion tube should fit easily with no force applied.

•

Locate three diameter template slots in front of endoscope

processing support.

•

Place portion of insertion tube closest to bending rubber into

smaller of template slots. If insertion tube fits in this slot, use

insertion tube sleeve labeled with a

RED

dot.

•

If insertion tube does not fit into this slot, go to next template slot.

•

If insertion tube fits into next template slot, use insertion tube

sleeve labeled with a

BLUE

dot.

•

If insertion tube does not fit into this slot, go to next template slot.

•

If insertion tube fits in this larger slot, use insertion tube

sleeve

NOT labeled

with a color dot

(split insertion tube

sleeve).

NOTE: Some endoscopes have a distal tip that is larger than
the insertion tube diameter. These endoscopes will fit into a
template slot but the distal tips will not fit into the designated
insertion tube sleeve. Use the split insertion tube sleeve
(NOT labeled with a color dot) to process these endoscopes.

•

If insertion tube does not fit into any template slot, endoscope

does not need an insertion tube sleeve.

CAUTION – POSSIBLE EQUIPMENT

DAMAGE: When using insertion
tube sleeve, ensure that sleeve
handle

is

pushed

down.

Insertion

tube

must

be

inserted over sleeve handle to
avoid possible damage.

Insertion Tube

Distal Tip

Insertion Tube

Figure 4-4. Carefully Insert Insertion Tube in Template Slot

Front o

f Endo

scope

Proce

ssing S

upport

Insertion Tube

Diameter

Template Slots

Place Insertion

Tube (NOT

Insertion Tube

Distal Tip) in

Template Slot

«
...
50
51
52
53
54
...
»

Содержание P920011-649









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P920011-649

Бренд: Rath Страницы: 3

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: ACE INSTRUMENTS Страницы: 15

Бренд: Wave Fitness Страницы: 15

Бренд: Bang & Olufsen Страницы: 2

Бренд: ICELED Страницы: 4

Бренд: Facom Страницы: 4

Бренд: FaceLake Страницы: 2

Бренд: IBEX Страницы: 4

Бренд: Jacobsen Страницы: 16

Бренд: Jacobsen Страницы: 20

Бренд: Jacobsen Страницы: 100

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: NanoVibronix Страницы: 2

Бренд: NanoVibronix Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды