Steris P920011-649 Скачать руководство пользователя страница 77

Страница: 77 / 168

4-32

920011-649

Operator Manual

Processing Instructions

NOTE:

When using bar code reader, note the following:

1) Customizable STERIS bar code lists are included in

instructions for "Bar Code Reader Installation" (P920011-
654).

2) Alphanumeric bar codes present on devices or identification

cards (with a maximum of 20 alphanumeric characters) can
also be used with bar code reader.

3) To bypass each scanning sequence, press START touch pad

instead of scanning bar code. Printout indicates scan was
bypassed.

4) During scanning sequence, press STOP touch pad at any

time to cancel and return to Ready mode.

6. Aim bar code reader at appropriate code on bar code list and press

trigger. Adjust reader position so scanning line is centered on code.
When bar code reader reads code correctly, a beep sounds and

display shows:

Programmed data is printed (see Figures 4-24 and 4-25).

NOTE:

If invalid bar code is scanned, display shows: "OPERATOR

ID IS INVALID" alternating with "(OPERATOR ID), STOP = RETRY".

7. Press

START

touch pad to confirm Operator ID, or

STOP

touch

pad to cancel and scan another bar code.

8. Repeat for each of the following bar code IDs:

•

Scan Boot A Patient ID; Scan Boot B Patient ID (DOUBLE

endoscope processing cycle only)

•

Scan Boot A Device ID; Scan Boot B Device ID (DOUBLE

endoscope processing cycle only)

•

Scan Boot A Procedure ID; Scan Boot B Procedure ID

(DOUBLE endoscope processing cycle only)

•

Scan Boot A Physician ID; Scan Boot B Physician ID

(DOUBLE endoscope processing cycle only)

NOTE:

If incorrect bar code is scanned, display shows for example:

"PHYSICIAN ID IS INVALID" alternating with "(PHYSICIAN ID),
STOP = RETRY".

9. Press

START

touch pad to start selected cycle. Once cycle is

started, display shows, for example:

(OPERATOR ID)

START = CONFIRM

OPERATING

MMM MIN

WARNING – EYE INJURY

HAZARD: Laser radiation. Do
not stare at bar code reader
beam.

Содержание P920011-649









































































































































































Результаты поиска

Содержание P920011-649

Отзывы:

Похожие инструкции для P920011-649

Бренды по названию

Популярные бренды

Steris P920011-649, Руководство оператора

Результаты поиска

Содержание P920011-649

Отзывы:

Похожие инструкции для P920011-649

Бренды по названию

Популярные бренды