Steris P920011-649 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 168

background image

4-44

920011-649

Operator Manual

Processing Instructions

4.11 Post-Processing

Checklist

The following conditions are necessary to achieve successful

processing of the endoscopes and accessory types listed in the

Endoscope Quick Reference Guide

:

�

Cycle is complete and printout "READY TO UNLOAD" message

verified (see

4.9.1, VERIFICATION 1 – P

);

�

No water is present in sump (see

S

ECTION

4.9.1, VERIFICATION 1

–

P

ARAMETRIC

C

ONTROLS

);

�

Reliance dry chemistry container and Reliance CDS are verified for

absence of solid residue (see

S

ECTION

4.9.2, VERIFICATION 2

–

P

ROCESS

);

�

Chemical indicator is verified to confirm a complete color

change (see

S

ECTION

4.9.2, VERIFICATION 2

–

P

ROCESS

);

�

If used, all Flow Units remained attached to the endoscope and

accessories (see

S

ECTION

4.9.3, VERIFICATION 3

–

P

HYSICAL

);

�

All endoscopes, accessories and adaptors are removed from

endoscope processing support.

If all above items are satisfactory, the endoscope processing
cycle is complete.

4.12 Pause or Abort

Cycle

If the operator, for any reason, wants to perform a verification inside

the chamber during a cycle, the processor operation can be halted

at any time by pressing the

STOP

touch pad. Once interrupted,

cycle either can be resumed or not, depending on the cycle phase in

progress. This is determined automatically by the control and the

display will show appropriate message.
1. To pause a cycle in progress, press

STOP

touch pad once. If

cycle was in a FILLING segment when interrupted, chamber is

first drained. Display shows:

alternating with:

If the cycle was in a heated segment when interrupted, chamber

is first cooled down. Display shows:

DRAINING

PLEASE WAIT

STOP PRESSED

CYCLE DELAYED

COOLING

PLEASE WAIT

WARNING

–

PERSONAL INJURY

AND/OR EQUIPMENT DAMAGE
HAZARD:  In  an  emergency,
stop  cycle  by  pressing  STOP
touch  pad  twice  to  abort
cycle.  Wait  for  processor  to
complete  Abort  sequence.
Wear  appropriate  Personal
Protective  Equipment  (PPE)
when reaching into chamber.

«
...
87
88
89
90
91
...
»

Содержание P920011-649









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P920011-649

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: VeEX Страницы: 2

Бренд: JB-Lighting Страницы: 48

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Cutler-Hammer ATC-300

Бренд: Eaton Страницы: 32

i-limb access hand

Бренд: Össur Страницы: 246

PROPRIO FOOT PSX01

Бренд: Össur Страницы: 374

Бренд: Marani Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды