Siemens SIMATIC MV540 H Скачать руководство пользователя страница 181

Страница: 181 / 238

Service and maintenance

10.1 Error and diagnostics messages

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

181

10.1.4

Read and verification error messages

If a read error or verification error occurs, the following error codes and error messages are

output. You can find additional information in the section "Overall result" of the online help.

Note
The causes of error 4700 to 4722 are also output in the verification report if there is a

verification error
All verification grades are output in the report as "E". The verification values correspond to

the error code.

Note
Evaluating verification errors as read errors
If the "Evaluate quality 'Poor' as "N_OK" check box has been selected in the decoding

settings, a verification error will also be evaluated as "N_OK".

Table 10- 3 Read/verification error messages

Error code

(%c)

Error message

(%s)

Description

0001

No 1D/2D code found in step n

No code was found in step #n.

0002

Cycletime too short

The processing was not completed within the cycle

time limit.

0003

Trigger too fast

The processing was interrupted by a trigger signal.

0004

Non ECC200 Code in step n

A data matrix code was found in step #n that does not

correspond to ECC200.
Note:

The check for ECC200 is performed only in adjust-

ment mode and during "Save program".

0005

Step n: Structured Append DMC not supported

In step #n, a "Structured Append" DMC type was

found. This DMC type is not supported.

0006

Step n: Reader Programming DMC not supported In step #n, a "Reader Programming Code" DMC type

was found. This DMC type is not supported.

0007

Step n: QR ECI encoding not supported

In step #n, a QR code with "ECI encoding" was found.

This QR type is not supported.

0008

Step n: QR Byte encoding not supported

In step #n, a QR code with "Byte encoding" was

found. This QR type is not supported.

0009

Step n: QR Kanji encoding not supported

In step #n, a QR code with "Kanji encoding" was

found. This QR type is not supported.

0010

Step n: Structured Append QR code not support-

In step #n, a "Structured Append" QR type was found.

This QR type is not supported.

0011

Step n: QR FNC1 encoding not supported

In step #n, a QR code with "FNC1 encoding" was

found. This QR type is not supported.

0012

Code quality is poor in step n

A code with "poor" quality evaluation was read in

step #n during verification.

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды