Siemens SIMATIC MV540 H Скачать руководство пользователя страница 26

Страница: 26 / 238

Safety notes

SIMATIC MV500

Operating Instructions, 06/2018, C79000-G8976-C494-01

System expansions

Install only system expansions that are intended for this device. Installing other expansions

can damage the system or violate the safety provisions and regulations for radio interference

suppression. You can obtain information on system expansions suitable for installation from

the technical customer service or from the sales office responsible for your area.

NOTICE
Invalidation of the warranty
Any damage to the device caused by installing or replacing system expansion products will

void the warranty.

NOTICE
Voltage can destroy electrostatic-sensitive modules
The device contains modules that are sensitive to electrostatic discharge. ESD devices can

be destroyed by voltages well below the threshold of human perception. Such voltages

occur if you touch a component or electrical connectors of a module without first

discharging the static from your body. The damage caused by overvoltage on a module

cannot normally be detected immediately and only becomes apparent after a longer period

of operation.
Measures for protecting against discharge of static electricity:

•

Before working with modules, make sure that you discharge static from your body, for

example by touching a grounded object.

•

The devices and tools used must also be free of static charges.

•

Interrupt the power supply.

•

Pick up the modules only on their edges and do not touch any pins or printed

conductors.

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды