Siemens SIMATIC MV540 H Скачать руководство пользователя страница 55

Страница: 55 / 238

Network and system integration

4.3 System configuration of the optical reader as PROFINET IO device with CM and FB 79 or Ident profile

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

4.3

System configuration of the optical reader as PROFINET IO device

with CM and FB 79 or Ident profile

Note
Power supply using "Power over Ethernet" (PoE)
If the optical reader is supplied by PoE, for example when connected to a

SCALANCE X108POE, the Power IO RS232 cable is not needed.

①

Optical sensor or light barrier (for trigger signal)

②

Object with code

Figure 4-2

Example: System configuration of the optical reader as PROFINET IO device and FB 79

or Ident profile

System characteristics

●

There is a connection to a PROFINET IO-capable S7 controller via Ethernet and a switch.

●

The optical reader is controlled by the S7 controller.

●

The result output of the test objects takes place via PROFINET IO to the S7 controller.

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды