Siemens SIMATIC MV540 H Скачать руководство пользователя страница 221

Страница: 221 / 238

Appendix

A.2 Certificates, approvals & guidelines

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

221

Country-specific EMC approvals

Table A- 2

USA

Approval

Description

Federal Communi-

cations Commission

Radio Frequency

Interference State-

ment

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment gen-

erates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interfer-

ence to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be re-

quired to correct the interference at his own expense.

Shielded Cables

Shielded cables must be used with this equipment to maintain compliance with

FCC regulations.

Modifications

Changes or modifications not expressly approved by the manufacturer could

void the user’s authority to operate the equipment.

Conditions of Opera-

tions

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful interfer-

ence, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Table A- 3

Canada

Approval

Description

Canadian Notice

This Class B digital apparatus complies with Canadian ICES-003.

Avis Canadien

Cet appareil numérique de la classe b est conforme à la norme NMB-003 du

Canada.

Declaration of Conformity

The EC Declarations of Conformity and corresponding documentation is available to the

responsible authorities according to the above-mentioned EC directive at the following

address:
Siemens Aktiengesellschaft

Division Process Industries and Drives

Process Automation
DE-76181 Karlsruhe
Germany
Your marketing contact can provide these if requested.

Installation guidelines

The installation guidelines and safety notices specified in the documentation must be

adhered to during commissioning and operation.

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды