Siemens SIMATIC MV540 H Скачать руководство пользователя страница 185

Страница: 185 / 238

Service and maintenance

10.1 Error and diagnostics messages

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

185

10.1.6

Diagnostics via the LED display

The operating states of the optical reader are indicated by the LEDs POWER (PWR),

ERROR (ER), RUN/STOP (R/S), LINK (LK), CONNECT, and READ. The LEDs can adopt

the colors green, red or yellow and the states off , on , flashing :

Table 10- 5 Display of operating states

LED

labeling

Meaning

Description and corrective measures

PWR

Green flashing:

•

Signals the startup phase after switching

on the optical reader.

•

Indicates an active firmware update that

must not be interrupted.

Wait until this is completed and the optical reader is opera-

tional.

Green, permanently on:

The optical reader is ready for operation

No error

Red, permanently on:

The optical reader is in "Group error" mode
Possible causes when working with onboard

PROFINET IO:

•

Bus communication is interrupted.

•

Bus error (no physical connection to a

subnet / switch).

•

Wrong transmission speed,

Full duplex transmission is not enabled.

•

The IP address is incorrect.

•

Bad configuration.

•

Bad parameter assignment.

•

Bad or missing device name.

•

I/O controller not available / switched off.

Start the WBM to view the error message. Perform the

suggested corrective measures in the section "Error mes-

sages (Page 176)".

•

Check whether the IP address or device name occurs

more than once in the network.

•

Check the settings of the I/O controller.

R/S

Permanently off:

The optical reader is in "Stop" mode.

No error

Green, permanently on:

The optical reader is in "RUN" mode.

No error

Permanently off:

There is no Ethernet connection to the opti-

cal reader.

•

Check the connection to the Ethernet cable.

•

Check whether the connected switch or other communi-

cations partner is operational.

•

Check or replace the Ethernet cable.

Green, permanently on:

An Ethernet connection without data traffic is

available.

In order to start the WBM of the optical reader, you also

need a valid network configuration for TCP/IP. Here, for

example, you can use the Primary Setup Tool to create a

valid network configuration for TCP/IP.

Green flashing:

The optical reader is exchanging data.

No error

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды