manualshive.com logo in svg

Siemens SIMATIC MV540 H, Руководство по эксплуатации


Поделиться
Скачать
background image

 

Process interfacing via an automation system (PLC, PC) 

 

9.3 Control with Ident profile 

SIMATIC MV500 
Operating Instructions, 06/2018, C79000-G8976-C494-01 

111

 

9.3.2.1

 

Status display of the optical reader 

 

 

Note 
Startup of the optical reader with Ident profile 
You need to perform the following steps after the power "ON" when starting up the optical 

reader while using the Ident profile (with or without a communication module): 
1.

 

Set a startup flag in OB100 of the controller. 

2.

 

Repeat the initialization ("init_run" or "INIT" command) until the initialization receives a 

positive acknowledgment. 

3.

 

To generate an error in the automation system, also monitor the maximum wait time for 

positive acknowledgment of the initialization and expected status bit values (only 

necessary if there is initialization without program selection). 

 

The status bits "IN_OP" (in operation) and "RDY" (ready) of the optical reader indicate 

whether the device has a group error, is in processing mode or is in STOP mode: 

Table 9- 7 

States of the optical reader 

RDY (ready) 

IN_OP (in operation) 

Description 

X 

0 

Group error 

1 

1 

Processing mode 

0 

1 

Stop or adjustment mode 

Depending on the state of the optical reader, different MV commands are permissible (see 

section "Preconditions for the commands (Page 124)") or an acknowledgment of an error 

(see section "Group error (Page 125)") is required before the next MV command can be 

issued. 
When there is a group error, this error must be acknowledged before further operation is 

possible. The acknowledgment mechanism is explained in the section ""PHYSICAL WRITE" 

commands / MV command interface (Page 112)". 
The status display is only valid after successful initialization. The "INIT" bit must be set for 

this. 

Table 9- 8 

Output parameters of the Ident profile 

Bit 

Description 

UIN0 

Corresponds to "IN_OP" bit of the optical reader 

UIN1 

Corresponds to "RDY" bit of the optical reader 

UIN2 

These two bits are interpreted as an 'unsigned' value (bit 2 is the less significant 

bit) that represents the number of available decoded codes. If the value = 3, 

three or more decoded codes are available. 

UIN3 

Содержание SIMATIC MV540 H















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC MV540 H

Nederman NEX S User Manual preview
NEX S
Бренд: Nederman Страницы: 89
Nederman MagnaTrack ST User Manual preview
MagnaTrack ST
Бренд: Nederman Страницы: 71
Nederman 30S Series User Manual preview
30S Series
Бренд: Nederman Страницы: 131
X-Cite TURBO Quick Start Manual preview
TURBO
Бренд: X-Cite Страницы: 2
Yamaha TG300 Sound List & Midi Data preview
TG300
Бренд: Yamaha Страницы: 39
Yamaha MU100 Supplementary Manual preview
MU100
Бренд: Yamaha Страницы: 110
Kärcher SP 16.000 Dirt Manual preview
SP 16.000 Dirt
Бренд: Kärcher Страницы: 148
zapco AGSP4-SL Owner'S Manual preview
AGSP4-SL
Бренд: zapco Страницы: 14
Electro-Music Klee Sequencer Building Instructions preview
Klee Sequencer
Бренд: Electro-Music Страницы: 120
EZ Digital OS-5060A Operation Manual preview
OS-5060A
Бренд: EZ Digital Страницы: 53
Vega VEGAMET 308 Technical Information & Operating Instructions preview
VEGAMET 308
Бренд: Vega Страницы: 8
Tactile Medical Entre Plus User Manual preview
Entre Plus
Бренд: Tactile Medical Страницы: 40
3M Peltor Workstyle HTRXS7A Manual preview
Peltor Workstyle HTRXS7A
Бренд: 3M Страницы: 10
Tadano TR-800XXL4 Manual preview
TR-800XXL4
Бренд: Tadano Страницы: 16
MIMAKI TS300P-1800 Product Manual preview
TS300P-1800
Бренд: MIMAKI Страницы: 44
SINTERIT SANDBLASTER SLS Original Manual preview
SANDBLASTER SLS
Бренд: SINTERIT Страницы: 20
WDT Granudos 45/100-Touch Operating And Installation Instructions preview
Granudos 45/100-Touch
Бренд: WDT Страницы: 138
Neumo 66TX51341313131 Operating & Installation Instructions Manual preview
66TX51341313131
Бренд: Neumo Страницы: 92

Бренды по названию

Популярные бренды

Загрузить еще бренды