Siemens SIMATIC MV540 H Скачать руководство пользователя страница 50

Страница: 50 / 238

Image processing

3.3 Options for image acquisition and image processing

SIMATIC MV500

Operating Instructions, 06/2018, C79000-G8976-C494-01

Each evaluated program uses the cycle time limit specified in this program. The maximum

cycle time for the complete program sequence thus corresponds to the sum of the maximum

cycle times of the activated programs.

"Best read result" and "All read results" settings

In program sequence mode, as with the image acquisition option "Scan", you can use the

"Best read result" and "All read results" settings.
Differences between "Best read result" and "All read results" settings:

●

If you select "Best read result", a processing attempt is always made with all activated

programs. All successful evaluations are compared based on a selectable quality

criterion. The qualitatively best result is output.

●

If you select "All read results", a processing attempt is also made with all activated

programs. All successful evaluations are output.

Same image settings for all programs to be evaluated

If you want the same image settings to be used for all programs to be evaluated, you can

also activate the "Use 1st image" option. In this case, only one image acquisition is made for

each trigger. The settings of the program in the program sequence that has the lowest

number are used. The image acquired is then used for processing for all programs in the

program sequence.

3.3.5

Simple comparison for Track&Trace (MATCH mode/command)

Note
MATCH command not suitable for changing during production
The MATCH command is not suitable for switching during ongoing production.

The match string can already be pre-defined for non-complex match tasks when saving the

program. For a simple MATCH command, this can be done by a connected controller or a

PC.
MATCH is available via the interface for PROFINET (Ident), TCP, RS232 and

communication module. The MATCH command and its structure are described in detail in

the section "Process interfacing via an automation system (PLC, PC) (Page 103)".

Static match default when saving a program

For applications in which the match default is already known during commissioning, the

match can be defined and activated when the program is saved. You can enable match

mode for 1D/2D codes in the "Match" drop-down list from the "Program > Decoder >

MATCH" menu in the WBM.

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды