Siemens SIMATIC MV540 H Скачать руководство пользователя страница 178

Страница: 178 / 238

Service and maintenance

10.1 Error and diagnostics messages

SIMATIC MV500

178

Operating Instructions, 06/2018, C79000-G8976-C494-01

Error

message

Value
Onboard

PROFINET

Value
TCP/IP and

RS232

Value
Ident

profile,

STATUS

byte

Description

Corrective measures

Error
Archiving/

MMI commu-

nication

W#16#500E

E1FE01

Error in communication

over the archiving connec-

tion: There is no TCP

connection, the server

does not respond within

the set time limit or vio-

lates the archiving proto-

col.

Check the connection to the

server. Make sure that the data is

processed by the server in an

adequately short time and that

the protocol is maintained.

Error
Lamp over-

load

W#16#500F

E4FE06

The connected lamp was

overloaded. The config-

ured or specified "Maxi-

mum duty cycle" under

"Settings > Options >

Lighting" has been ex-

ceeded.

Decrease the trigger frequency,

reduce the exposure time or use

a more powerful lamp.

Error
invalid pro-

gram number

W#16#5010

E6FE04

An attempt is being made

to save a program under

an invalid number via the

interface set in "Control-

ler".

Select a program number be-

tween 1 and 15.

Error
PROFINET

IO connec-

tion error

W#16#5012

PROFINET IO connection

termination

The connection to the

PROFINET IO controller was

interrupted. Check the connec-

tion to the I/O controller.

Error
PROFINET

IO controller

status

"STOP"

PROFINET IO controller

is in "STOP" status
Note:

No diagnostic interrupt is

sent to the I/O controller

The PROFINET controller is in

"STOP" mode, which means it

cannot receive commands from

the optical reader. Make sure

that the I/O controller changes

back to "RUN" status.

Error
PROFINET

I/O configura-

tion error

W#16#5016

Faulty PROFINET IO

configuration

The PROFINET IO configuration

of the optical reader and that of

the communication partner do

not match. Check the PROFINET

mode in the optical reader and in

the I/O controller.

Error
PROFINET

IO compatibi-

lity error

W#16#5017

Version incompatibility of

the PROFINET IO control-

ler to the I/O device (opti-

cal reader)

The version of the I/O controller

is out of date and not compatible

with the current version of the

optical reader.
To correct this error, we recom-

mend that you upgrade the I/O

controller.

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды