Siemens SIMATIC MV540 H Скачать руководство пользователя страница 149

Страница: 149 / 238

Process interfacing via an automation system (PLC, PC)

9.4 Control with FB 79

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

149

Sequence when resetting the DISA bit ("COMMAND" = W#16#0005)

The block resets the "DISA" bit in the control byte of the optical reader. The "DONE"

parameter then has the value "TRUE" and "ACTIVE" the value "FALSE".

Note
No edge change detected
Because the job completes in one CPU cycle, no edge change can be detected at the

"ACTIVE" parameter. If the "DONE" parameter already has the value "TRUE" from a

previous job, it is also not possible to detect an edge change.

Sequence of the read jobs ("COMMAND = W#16#0081 ... W#16#008F")

Table 9- 48 Possible values of the "COMMAND" parameter for the read jobs

Value (W#16#...) Meaning
0081

Output result string

0082

Output absolute quality characteristics

0083

Output absolute quality characteristics and output result string

0084

Output quality characteristics as classes

0085

Output quality characteristics as classes and output result string

0086

Output quality characteristics as classes and in absolute format

0087

Output quality characteristics as classes and in absolute format and output result

string

0088

Output code position

0089

Output code position and result string

008A

Output code position and absolute quality characteristics

008B

Output code position and absolute quality characteristics and output result string

008C

Output code position and quality characteristics as classes

008D

Output code position and quality characteristics as classes and output result string

008E

Output code position and quality characteristics as classes and in absolute format

008F

Output code position and quality characteristics as classes and in absolute format

and output result string

The read jobs can only be sent when the optical reader is not in RUN mode (see also the

operating state table following the parameter table).
In contrast to all other jobs, the read jobs are "permanent jobs". This means that the

"ACTIVE" parameter retains the value "TRUE" even after fetching the current read result

and/or the current position and/or the quality characteristics from the optical reader.

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды