Siemens SIMATIC MV540 H Скачать руководство пользователя страница 179

Страница: 179 / 238

Service and maintenance

10.1 Error and diagnostics messages

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

179

Error

message

Value
Onboard

PROFINET

Value
TCP/IP and

RS232

Value
Ident

profile,

STATUS

byte

Description

Corrective measures

Error
CPU temper-

ature too high

W#16#5018

The temperature of the

CPU is outside the valid

range. This can lead

to incorrect read results,

shortened service life or

destruction of the reader.

Ensure there is adequate ventila-

tion or cooling of the reader and

ensure that the ambient tempera-

ture is within the permissible

range.

Error
Lens temper-

ature too high

W#16#5019

The temperature of the

lens is outside the valid

range. This can lead

to incorrect read results,

shortened service life or

destruction of the reader.

Ensure there is adequate ventila-

tion or cooling of the reader and

ensure that the ambient tempera-

ture is within the permissible

range.

No message --

E4FE84

Error in last command

sequence
Note:

No diagnostic interrupt is

sent to the I/O controller.

May occur if triggering is too fast.

The Ident profile can only pro-

cess one command at a time

before a new command can be

executed.

Self-acknowledging connection errors

The following connection errors are self-acknowledging:

●

Error "TCP communication"

●

Error "Archiving/MMI communication"

●

Error "PROFINET IO connection error"

●

Error "PROFINET IO controller status 'Stop'"

As soon as the connection is re-established after an interruption, the optical reader exits the

error state. The optical reader returns to the mode prior to the occurrence of the error, for

example, back to processing mode.
The occurrence of these errors and their automatic acknowledgment are stored in the

diagnostic data records. Stored error messages are not overwritten by newer errors.
If there are error entries, a corresponding note appears in the WBM during processing mode

("Start") in the "Program > Info statistics" area.

Note
PROFINET IO error / OB 86 not programmed
Note that the occurrence of a PROFINET IO error in a SIMATIC S7 controller causes OB 86

(rack failure OB) to be called. If you have not programmed OB 86, the controller goes to the

"STOP" state.

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды