Siemens SIMATIC MV540 H Скачать руководство пользователя страница 7

Страница: 7 / 238

Preface

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

Firmware encryption

The firmware itself is signed and encrypted. This ensures that only authentic firmware can be

downloaded to the device.

Secure/non-secure protocols

●

Check whether it is necessary to use SNMPv1. SNMPv1 is classified as non-secure.

Make use of the possibility to prevent write access. The product offers corresponding

settings for this.

●

If SNMP is activated, change the community names. If unrestricted access is not

necessary, limit access via SNMP.

●

Use secure protocols if access to the device is not protected by means of physical

safeguards.
The following protocols provide secure alternatives:

HTTP → HTTPS

●

To prevent unauthorized access to the device or network, set up appropriate safeguards

against non-secure protocols.

●

Enable only the services (protocols) that will actually be used on the device. The same

applies to the installed interfaces/ports. Unused ports could be used to access the

network downstream from the device.

List of available protocols

All available protocols and their ports that are used with SIMATIC MV500 are listed below.

Table 2

List of available protocols

Protocol

Port number

Default port

status

Port activation

Authentication

Encryption

HTTP

TCP/80

Open

HTTPS

TCP/443

Open

Yes

NTP

UDP/123

Closed

✓

TCP

TCP Config

Closed

✓

SSH

TCP/22

Closed

✓

Yes

DNS

TCP/53

Closed

DHCP

UDP/68

Closed

SNMP

UDP/161

Open

Yes

PROFINET

UDP/34964
UDP/57345-57346

Open

Scanner portal

TCP/666

Closed

✓

MMI

TCP dynamic

Closed

✓

ALM LIC

TCP/65278

Open

This protocol is only used when the "CONNECT" button is used.

Only when the reader is in "Stop".

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды