Siemens SIMATIC MV540 H Скачать руководство пользователя страница 183

Страница: 183 / 238

Service and maintenance

10.1 Error and diagnostics messages

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

183

Error code

(%c)

Error message

(%s)

Description

4708

Mean light outside of range in step n: Cycle time

limit of the automatic exposure control reached

The average brightness needed for ISO/IEC 29158 is

outside the valid range (see Error code 4709).
The automatic exposure control was unsuccessful

because the necessary decodings could not be com-

pleted within the time limit.

To resolve this error:

•

Reduce the exposure ROI of the program.

•

Increase the time limit of the exposure control.

•

Also ensure that the code is completely within the

exposure ROI until conclusion of the image acqui-

sition process.

4709

Mean light outside of range in step n

The average brightness needed for ISO/IEC 29158 is

outside the valid range (70% to 86%) in step #n.

4710

Verification failed in step n: Data Matrix ECC200

required

Verification requires a data matrix code according to

ECC200 specification (only for verification according

to ISO/IEC 15415 or ISO/IEC 29158).

4711

Verification failed in step n: Aperture too small

The cell size of the data matrix code in step #n is too

large for the configured aperture (only for verification

according to ISO/IEC 15415).

4712

Verification failed in step n: Aperture too large

The cell size of the data matrix code in step #n is too

small for the configured aperture (only for verification

according to ISO/IEC 15415).

4713

Verification failed in step n: Not enough space

around the Data Matrix

The quiet zone around the data matrix contained in

the image is too small. For verification, a quiet zone of

at least the size of two cells is required (only for verifi-

cation according to ISO/IEC 15415 or 29158).

4714

Verification failed in step n: RDA could not find

the horizontal timing pattern

The reference decoding according to

ISO/IEC 16022:2006 signals an error when searching

for the horizontal timing pattern (only for verification

according to ISO/IEC 15415 or ISO/IEC 29158).

4715

Verification failed in step n: RDA could not find

the vertical timing pattern

The reference decoding according to

ISO/IEC 16022:2006 signals an error when searching

for the vertical timing pattern (only for verification

according to ISO/IEC 15415 or ISO/IEC 29158).

4716

Verification failed in step n: RDA found an incor-

rect number of rows and columns

The reference decoding according to

ISO/IEC 16022:2006 signals an error when determin-

ing the number of rows or columns (only for verifica-

tion according to ISO/IEC 15415 or ISO/IEC 29158).

4717

Verification failed in step n: RDA could not locate

the finder pattern

The reference decoding according to

ISO/IEC 16022:2006 signals an error when searching

for the finder pattern (only for verification according to

ISO/IEC 15415 or ISO/IEC 29158).

4719

Verification failed in step n: RDA error correction

failed

The reference decoding according to

ISO/IEC 16022:2006 signals an error when determin-

ing the error correction (only for verification according

to ISO/IEC 15415 or ISO/IEC 29158).

4720

Verification failed in step n: Number of Data Ma-

trix rows/columns is too high

The maximum supported code size for verification

according to ISO/IEC 15415 or ISO/IEC 29158 is

104x104 cells.

Содержание SIMATIC MV540 H















































































































































































































































Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды

Siemens SIMATIC MV540 H, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC MV540 H

Отзывы:

Похожие инструкции для SIMATIC MV540 H

Бренды по названию

Популярные бренды