RTI Piranha Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 181

RTI Piranha Скачать руководство пользователя страница 79

4. Measurement Principles & Theory

Update Modes

2014-06/5.5C

75

Piranha & QABrowser Reference Manual

Update Modes

4.3

As described under

Measurement Type

Settings

and seen in the figure to the left,

the following four update modes are
available:

After exp.

, the QABrowser receives a new value when the exposure terminates. This

means when the output goes under the trig level and stays there at least the time
set by Post Delay under

Settings | Piranha

. Reset time is one second.

Continuous

, the Piranha is continuously sending data as long as radiation is

detected. Displays in the QABrowser are updated about every four seconds.
Typically used for Fluoroscopy. Reset time is one second.

Timed

, the user sets a measurement time. The user then starts the measurement

and the Piranha will measure all radiation received during the measurement time,
without any trig levels or background compensation. When the time has passed, a
reading will be presented. It has a long reset time for increased accuracy, which
varies with the sensitivity, as seen in the table below.

Free run

, the Piranha will continuously measure the radiation without any trig

levels or background compensations. No applications are available when using this
mode. The mode has a feature called moving average which calculates the
average of the measured values during a defined time, to increase accuracy by
lowering the time resolution. This function gives a larger stability to the
measurements. Free run also has a long reset time for increased accuracy, see
the table below.

In Ocean the

Normal Mode

automatically handles

After exp.

and

Continuous

modes.

Default value is set according to selected type of measurement and this parameter
normally never needs to be manually changed, unless really low-level measurements
are to be accomplished.
However, to measure on real low-level signals the

Timed

or

Free run

update mode may

be used

74

«
...
77
78
79
80
81
...
»

Содержание Piranha






















































































































































































Отзывы:

Нет отзывов