RTI Piranha Скачать руководство пользователя страница 70

Страница: 70 / 181

3. Description of the QABrowser
QABrowser Setup

Piranha & QABrowser Reference Manual

2014-06/5.5C

3.7.5

Detector Information

The detector information screen lists all detectors available for the system. For each
module you can see the available detectors and probes.

3.7.6

System Info

System Info

is used to get information about the Piranha

system.

Serial Number

The serial number for the system.

Firmware

Firmware version of the internal software that is used in the system.

Product v.

The product version is the hardware version. This is the version
printed on the product serial label.

3.7.7

System Test

System Test

is used to test different functions in the

Piranha system.

Beep

generates a 2 second beep.

Play Melody

plays the famous Swedish hit song, "The

Final Countdown".

Filter Test

moves the filter in a special sequence and

makes a double beep for each position. The sequence is
4-5-4-C-1-2-3-4-5-4-3-2-1-C.

Содержание Piranha






















































































































































































Результаты поиска

Содержание Piranha

Отзывы:

RTI Piranha, Справочное руководство, Страница: 70 / 181

Результаты поиска

Содержание Piranha

Отзывы: