RTI Piranha Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 181

RTI Piranha Скачать руководство пользователя страница 46

3. Description of the QABrowser
Real-time Display and Waveforms

Piranha & QABrowser Reference Manual

2014-06/5.5C

42

The single parameter displays are large to allow reading from distance. In the single
parameter displays complementary values may be shown (in the figure above exposure
time and total filtration). Which complementary values that are shown depends on the
selected parameter. Up to three complementary values can be shown.

If any of the displayed values is not possible to compensate or cannot be measured with
full accuracy the symbol

is displayed at the top of screen. If the symbol is displayed

you can tap it with the pen to display more information.

3.3.2

Waveforms - Acquiring and Viewing

Waveforms are always captured for each exposure you make. Up to three waveforms
are simultaneously captured and visualized with the QABrowser. The following
waveforms can be measured depending on configuration and selected type of
measurement:

tube voltage (kVp) with the Internal detector
dose rate with the Internal detector
dose rate with the external Dose Probe (available for specific Piranha models).
tube current (mA) with the external Dose Probe (available for specific Piranha
models).

In Continuous update mode you also have the possibility to restart the waveform
collection during the measurement. Every time you tap

Hold

, the waveforms are

acquired again. When you do this, the previously acquired waveforms will be replaced.
The waveforms available for viewing will be the ones from you last

Hold

tap.

To view waveforms after the exposure:

1. Tap

Wave

(or press the corresponding

button). The waveform screen appears and
waveforms are displayed. The kV waveform
takes a few seconds to calculate before it is
displayed.

«
...
44
45
46
47
48
...
»

Содержание Piranha






















































































































































































Отзывы:

Нет отзывов