RTI Piranha Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 181

RTI Piranha Скачать руководство пользователя страница 122

5. Measurements with the Piranha System
Mammography

Piranha & QABrowser Reference Manual

2014-06/5.5C

118

1. Place the Piranha Dose Probe in the field and

connect the cable to the Piranha input.

2. Set up the Piranha and the handheld computer

according to the description in Setting Up the
Piranha for Mammography.

3. Follow the same step as for the measurements

with Piranha but select

Dose

as parameter. You

will also need to select the External detector.

4. Select radiation quality from the detector list.

5. Set kVp and mAs (or mA/time) to desired values.

6. Make an exposure.

7. Read the dose value. Note that the dose

reading has to be corrected manually
according to the Piranha Dose Probe
DETECTOR DATA manual.

You may store the correction as a

Beam Correction Factor

in a

Favourite

for a

specific kV, to do the correction
automatically.

8. Repeat the measurement for other generator settings.

To get a good HVL value, using the Piranha Dose Probe, you must correct
it according to the tables in the Piranha Dose Probe DETECTOR DATA
manual. It is often more convenient to measure HVL with the Piranha
using the built-in HVL application.

5.5.5

HVL Application

HVL is calculated in the standard way using an HVL stand and a set of Aluminium
filters.

Using the Piranha and the built-in HVL application is recommended since
a correct HVL value is then obtained without any manual corrections.

Set up the system the same way as described above to measure dose in
mammography beams. Depending of what protocol is used you can use the HVL stand
or place the filters on the compression paddle.

«
...
120
121
122
123
124
...
»

Содержание Piranha






















































































































































































Отзывы:

Нет отзывов