RTI Piranha Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 181

RTI Piranha Скачать руководство пользователя страница 63

3. Description of the QABrowser

Data Logging

2014-06/5.5C

59

Piranha & QABrowser Reference Manual

You can stop and save the log from the pull-down menu by selecting

Options

|

Save

Log

.

The contents of the log file is displayed. You can now:

Export
(only
PalmOS)

Export the log file to Memo Pad (a standard application in your
handheld). Read the manual for the handheld computer to get
more information about the Memo Pad.

Delete

Delete log file.

Favourites

3.6

From the beginning we sought to make the menu structure of the QABrowser very
intuitive and simple to use. For a new user it is very simple to go step-by-step and
perform a measurement and at the same time learn how the QABrowser works.
However, once you become familiar with the interface, and find yourselves performing
the same types of measurements over and over again, you may desire to move
between these types of measurements more quickly. Instead of going up and down
through the menu trees we found that users would like to move across the tree
structure. The desire was to find a solution for this need but still be able to keep the
simplicity and intuitiveness of the existing menu structure. The solution to this is a
feature called "Favourites". We will recognise this term from the web browsers. This is
how it works:

When you find a specific RTD or application for a specific
type of measurement that you perform on a regular basis
you can add it to the Favourites list.

You may give the Favourite a title or use the one
suggested by the QABrowser.

If you instead select

Start Here!

, a special Favourite will

be created, that gets you right back to this test, the next
time you start the QABrowser.

«
...
61
62
63
64
65
...
»

Содержание Piranha






















































































































































































Отзывы:

Нет отзывов