RTI Piranha Скачать руководство пользователя страница 24

Страница: 24 / 181

2. Description of the Piranha
Hardware and Specifications

Piranha & QABrowser Reference Manual

2014-06/5.5C

Parameter

Range

Dose/pulse

with wide range option (WR)

2.5 µGy/pulse - 60 kGy/pulse

8 nGy/pulse - 60 kGy/pulse

Pulse dose rate

with wide range option (WR)

Lower limit 10 µGy/s (70 mR/min), otherwise same as
for air kerma rate.
Lower limit 10 µGy/s (70 mR/min) otherwise, same as
for air kerma rate.

Min. output peak dose rate

- High Sensitivity

- Low Sensitivity

dose rate (min. pulse width)
4 µGy/s (4 ms) / 30 µGy/s (0.5 ms)
20 µGy/s (4 ms) / 160 µGy/s (0.5 ms)

Pulse rate

0.5 – 180 Hz, resolution 0.5 Hz

Pulse width

4 ms - 2000 s

Duty cycle

5 - 95 %

Minimum pulse width

- High Sensitivity

- Low Sensitivity

pulse width (min. dose rate)
4 ms (4 µGy/s) / 0.5 ms (30 µGy/s)
4 ms (20 µGy/s) / 0.5 ms (160 µGy/s)

Minimum ripple

(pulse top to bottom)

50 %

Irradiation time

1 – 65535 pulses, resolution 1 pulse

Note 1

: Max dose/pulse depends on the pulse length.

Note 2

: All kerma and kerma rate ranges, inaccuracy, and resolution figures are valid for product

version 2 and higher of the Piranha.

Waveform recording time

At max sampling rate

1024 ms (2 kSa/s)

At min sampling rate

524 s (4 Sa/s)

A total of 8 recording times are available, all separated by a factor of 2, i.e. 1, 2, 4, 8,
16, 33, 66, 131, 262 and 524 seconds.

The setting for

Waveform recording time

may affect the Irradiation time

calculation. Make sure to set back the

Waveform recording time

to the

lowest choice after temporarily modifying it. Please also note that in
QABrowser, the waveforms are limited to between 0.32 and 4 seconds.

Содержание Piranha






















































































































































































Результаты поиска

Содержание Piranha

Отзывы:

RTI Piranha, Справочное руководство, Страница: 24 / 181

Результаты поиска

Содержание Piranha

Отзывы: