manualshive.com logo in svg

RTI Piranha, Справочное руководство, Страница: 160 / 181

Поделиться
Скачать
RTI Piranha Скачать руководство пользователя страница 160

7. Problems and Solutions
Bluetooth

Piranha & QABrowser Reference Manual

2014-06/5.5C

 

156

Bluetooth connection).

7.2.2

Enable Bluetooth Passkey

Before you enable the use of a Bluetooth passkey please read the section about
Bluetooth passkeys and the drawbacks of using a passkey.

You enable and disable passkeys by using the 

RTI Updater

 application (requires

version 2008.6A or later) which is available on your RTI Software & Documentation CD
and the RTI website (

www.rti.se

).

1. Connect your meter using the USB cable. If you are using a Barracuda then also

connect the Barracuda Serial Bluetooth Module.

2. Launch RTI Updater from the RTI Electronics folder in the Windows start menu.
3. Select the USB connection. You cannot use a Bluetooth connection when you want to

change the Bluetooth configuration. A Bluetooth connection is shown as 

COMxx

.

4. Wait for RTI Updater to finish with the startup procedure. After a while when it is

ready the 

Start

 button will be enabled.

5. Select 

Settings | Advanced

 from the menu.

6. Now select the 

Tools

 menu.

7. If you want to enable the use of a passkey select 

Enable Bluetooth Passkey

. If you

experience problems with this, then you probably need to update you meter firmware
before you can enable the Bluetooth passkey. Please run the available updates (by
pressing 

Start

) and then restart the application again to enable the Bluetooth

passkey.

8. Follow the onscreen instructions.

If you want to disable the Bluetooth passkey do the same thing but select 

Disable

Bluetooth Passkey

 instead. If you are asked for a PIN code during the startup do 

not

enter a PIN code, just cancel instead. Because if you do, you will have activated your
Bluetooth and RTI Updater cannot reconfigure the Bluetooth module when it is active.

How To Report a Problem

7.3

There is a way of automatically sending technical support information to RTI Electronics
AB when you are experiencing problems with the QABrowser.

This is how you use that functionality:

1. HotSync the Palm handheld that you are experiencing the problem with.
2. On your PC, go to 

Start Menu | All Programs | RTI Electronics | QABrowser

Updater

 

and click 

Send Support Information

.

3. A dialogue window will be shown. Please enter a description of the problem. 

The more information you give, we will have better chances of reproducing the
problem and finding a solution to it.

4. Click 

Send

 to send the auto-generated email.

Содержание Piranha






















































































































































































Отзывы:

Нет отзывов