RTI Piranha Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 181

RTI Piranha Скачать руководство пользователя страница 41

3. Description of the QABrowser

Introduction to the QABrowser

2014-06/5.5C

37

Piranha & QABrowser Reference Manual

3

Description of the QABrowser

Introduction to the QABrowser

3.1

The QABrowser is a program that runs on a handheld computer. It will quickly guide you
through the measurements and tests of different X-ray systems. The QABrowser
controls the Piranha and provides an intuitive user-interface. The instrument is set-up
based on the type of measurement you select. Two main measuring modes are
available; real-time display (RTD) and application mode.

In real-time display mode "virtual" meters are shown allowing you to read real-time data.
Up to six values can be measured and displayed at the same time. The built-in
applications allow you to do different tests such as accuracy, reproducibility, linearity,
HVL, and CTDI. There are also applications for viewbox test and monitor test using the
light detector. The QABrowser also allow you to look at waveforms and log data.

The text in this section assumes that you purchased your Handheld Display either
directly from RTI or a RTI dealer, which means that QABrowser is already installed and
configured on the Handheld Display. If you have purchased your handheld on your own,
then you first need to install the QABrowser to the handheld. How to do this for Palm OS
handhelds is described in the installation chapter in the HTML Help file on your Product
CD.

Starting the QABrowser

3.2

Wireless through Bluetooth

1. Turn on the meter.
2. Launch the QABrowser by tapping on the QABrowser icon.

Please note that

All

needs to be selected at the top of the screen for the QABrowser

icon to be visible.

3. The handheld will now search for available Bluetooth devices and show them to you.
4. Select your meter and press OK.
5. If prompted enter the passkey for the meter which is “0000”.

If you experience any problems connecting through Bluetooth please see the

«
...
39
40
41
42
43
...
»

Содержание Piranha






















































































































































































Отзывы:

Нет отзывов