manualshive.com logo in svg

RTI Piranha, Справочное руководство, Страница: 72 / 181

Поделиться
Скачать
RTI Piranha Скачать руководство пользователя страница 72

3. Description of the QABrowser
Indicators and Symbols

Piranha & QABrowser Reference Manual

2014-06/5.5C

 

68

Indicators and Symbols

3.9

Different indicators (symbols) are used to indicate status and to guide you in different
situations. You can tap same of the indicators to get more information:

This symbol may be preceding a text or a value. It indicates that if you tap it,
a drop-down list with more choices will appear, allowing you to change the
corresponding value/text/setting.

This symbol indicates that settings information is available. Tap this icon to
open the additional information screen. Here are measurement information
and settings for the Piranha and its detectors found. This menu is accessed
when you need to override the default settings of the Piranha that are set by
the QABrowser. See topic 

Settings

 for more information.

This "play" symbol indicates that the system has been trigged, and the
continuous readings (fluoro) are being updated. When the radiation stops
this symbol will disappear and a green RTI logo will briefly be superimposed
over the whole screen. If you get this symbol when there is no signal press
reset. If it comes over and over you may need to increase the trig level, by
raising the threshold, see topic 

Settings

.

This "pause" symbol indicates that hold has been activated during
measurement on fluoroscopy.

This symbol indicates that there are more items not visible in a list. Tap the
symbol or press the up/down buttons to view not visible items.

This symbol is similar to the previous. Tap to move the cursor bar up and
down in the built-in applications (accuracy, linearity, reproducibility, and so
on). Grey arrows indicates that the end has been reached. It may also be
used to step between different "rows" in the Quickbar.

This symbol is also similar to the previous ones. It is used for the built-in
applications (accuracy, linearity, reproducibility, and so on), when multiple
parameters is measured, i.e. "All" etc. Tap left or right to move between the
different reading screens. Grey arrows indicates that the end has been
reached, as indicated by the text in between.

This is an animated symbol. Its "movement" indicates that the log is enabled
and active. Tap it to toggle between pause and active. 

This icon on the top left side of the Graffiti area takes you to the Favourites,
see section 

Favourites

.

This icon on the bottom left side of the Graffiti area is the menu icon.
Tapping this symbol brings down the drop-down menu from the top of the
screen.

43

43

59

Содержание Piranha






















































































































































































Отзывы:

Нет отзывов