RTI Piranha Скачать руководство пользователя страница 167 | Manualshive

Страница: 167 / 181

RTI Piranha Скачать руководство пользователя страница 167

8. Glossary

2014-06/5.5C

163

Piranha & QABrowser Reference Manual

devices such as source position, collimator opening, beam direction, door closure, filter
presence, and preventing the production or emission of radiation if the potential
for an unsafe condition is detected.

Ionization

Formation of ions by the division of molecules or by the addition or removal of electrons
from atoms or molecules.
SI unit: C, Coloumb

Ionization chamber

Ionization detector consisting of a chamber filled with a suitable gas, in which an electric
field, insufficient to induce gas multiplication, is provide for the collection at the
electrodes of charges associated with ions and the electrons produced in the sensitive
volume of the detector by ionizing radiation.

Ionization constant

For air the ionization constant W/e = 33,97 J/C. The ionization constant is used to get
the correspondence between exposure and air kerma. See Roentgen and Gray for more
information.

Ionization detector

Radiation detector based on the use of ionization in the sensitive volume of the
detector.

Irradiation time

Irradiation time is usually the time a rate of a RADIATION QUANTITY exceeds a
specified level. Irradiation time is sometimes called Exposure time.
SI unit: s, second

Kerma (K)

The sum of the initial kinetic energies of all the charged ionizing particles liberated by
uncharged ionizing particles per unit mass of a specified material. Kerma is measured in
the same unit as absorbed dose. The SI unit of kerma is joule per kilogram and its
special name is gray (Gy). Kerma can be quoted for any specified material at a point in
free space or in an absorbing medium. Typically the kerma is specified in air.
SI unit: Gy = J/kg

Kerma rate (K')

Kerma per unit time. Kerma rate is determined as the quotient of dK by dt, where dk is
the increment of kerma in the time interval dt: K'=dK/dt. A unit of kerma rate is any
quotient of the Gray or its multiples or submultiples by a suitable unit of time (Gy/s,
mGy/h, etc.).
SI unit: Gy/s = J/kg·s

Kilovolt (kV)

A unit of electrical potential difference equal to 1000 volts.

kVp

See Peak tube voltage

Lead equivalent

The thickness of lead affording the same attenuation, under specified conditions, as the
material in question.

«
...
165
166
167
168
169
...
»

Содержание Piranha






















































































































































































Отзывы:

Нет отзывов